Choose this Redwood composite fence gate for 1-inch gaps and a separate overhead connection. This horizontal semi-privacy single gate has 1-inch gaps, with nine full boards and one supplemental strip forming the specified leaf. The crossbeam does not turn it into a closed-board design.
The gate leaf remains nominally 6 ft high. Separate LINE stock is cut for the overhead member in the installation intended to meet a 7 ft fence, supported by two In-Ground steel posts. Compare semi-privacy fence layouts before choosing the adjacent sections. With composite fence gates, specify both the leaf spacers and the overhead fixing kit in the quote so a spaced leaf is not ordered from a closed-board list.
Choose this Redwood composite fence gate for 1-inch gaps and a separate overhead connection. This horizontal semi-privacy single gate has 1-inch gaps, with nine full boards and one supplemental strip forming the specified leaf. The crossbeam does not turn it into a closed-board design.
The gate leaf remains nominally 6 ft high. Separate LINE stock is cut for the overhead member in the installation intended to meet a 7 ft fence, supported by two In-Ground steel posts. Compare semi-privacy fence layouts before choosing the adjacent sections. With composite fence gates, specify both the leaf spacers and the overhead fixing kit in the quote so a spaced leaf is not ordered from a closed-board list.
Engineering Dimensions
Nominal size (width × height): 3.5 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 45⅝ inches.
Clear opening between posts: approximately 42½ inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
1-inch Spacer: powder-coated aluminum.
- The Redwood leaf uses a specified 1-inch-gap horizontal pattern.
- Nine full boards and one supplemental strip are recorded as ten installed pieces.
- Spacer components serve the leaf; separate fixing hardware serves the LINE crossbeam.
- The gate is a 6 ft leaf in the specified 7 ft fence connection.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 1 set
- Modern Yard™ Redwood Fence Board x 2.5 packs (10 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Accessory – 1-Inch Spacer for Horizontal Fence (40-Pack) x 0.4 pack (1-inch Spacer x 16 PCs)
- Modern Yard Line™ Fence Slat x 0.25 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Redwood boards and covered metal gate parts: up to 25 / 10 years.
- Covered Redwood board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock is outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Does the Crossbeam option change the gaps between boards?
No. This configuration retains its 1-inch-gap Redwood leaf. It adds the separately specified overhead connection and a different post layout from the ordinary gate.
Are all ten pieces full-width boards?
No. The source records nine full boards plus one supplemental strip. Keep that distinction instead of describing ten full boards.
Can I use only the full-privacy crossbeam kit to create the spaced leaf?
No. The crossbeam fixing kit and the composite leaf spacer components have different jobs. Follow both entries in this gate component plan.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPH/SGG10RD10-42X72-IG
In-Ground
Without Crossbeam
Style #: WPH/SGG10RD6-42X42-IG
In-Ground
With Crossbeam
Style #: WPH/SGFPRD11-42X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/SGDP16P01RD9DP1-42X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPH/SGFPRD11-42X72-IG
In-Ground
Without Crossbeam
Style #: WPH/SGDP16P01RD9DP1-42X72-IG





























