Leave spaces in the horizontal Redwood infill with this composite fence gate. Its two leaves use 1-inch gaps, with the composite infill and spacing components assembled into aluminum frames. The source counts 20 composite pieces overall, including the two supplemental strips in the specified layout.
A single LINE crossbeam distinguishes this version from the ordinary gate. It is intended for the connection to a 7 ft fence, using posts with 86 inches above ground and 28 inches embedded. The double fence gate has nominally 6 ft-high leaves and a 7 ft overall nominal width. Consult the stock and installation quantities separately when ordering. Compare semi-privacy choices for the adjoining fence before selecting this entrance.
Leave spaces in the horizontal Redwood infill with this composite fence gate. Its two leaves use 1-inch gaps, with the composite infill and spacing components assembled into aluminum frames. The source counts 20 composite pieces overall, including the two supplemental strips in the specified layout.
A single LINE crossbeam distinguishes this version from the ordinary gate. It is intended for the connection to a 7 ft fence, using posts with 86 inches above ground and 28 inches embedded. The double fence gate has nominally 6 ft-high leaves and a 7 ft overall nominal width. Consult the stock and installation quantities separately when ordering. Compare semi-privacy choices for the adjoining fence before selecting this entrance.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
1-inch Spacer: powder-coated aluminum.
- Horizontal Redwood infill uses the specified 1-inch gap layout.
- The complete infill count includes 18 main boards and two supplemental strips.
- One LINE crossbeam is separate from the gate's composite boards and spacers.
- The crossbeam configuration is intended to meet a 7 ft fence.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Redwood Fence Board x 5 packs (20 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ Accessory – 1-Inch Spacer for Horizontal Fence (40-Pack) x 0.8 pack (1-inch Spacer x 32 PCs)
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Redwood boards and covered metal gate parts: up to 25 / 10 years.
- Covered Redwood board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Is this a fully closed Redwood gate?
No. The 1-inch gaps make it a semi-privacy layout. It allows views through the infill and should not be described as fully screening every viewpoint.
Why are two strips mentioned within the total?
The source distinguishes 18 main pieces and two supplemental strips across the pair. Keep that installation layout separate from the five-pack stock allocation.
Does each leaf need its own crossbeam?
No. This double-gate configuration has one installed crossbeam for the pair, using the separate LINE stock and beam hardware shown in Component Needs.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPH/DGG10RD20-84X72-IG
In-Ground
With Crossbeam
Style #: WPH/DGFPRD22-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGDP16P01RD18DP2-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPH/DGFPRD22-84X72-IG
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01RD18DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPV/DGFPRD12-84X72-CB-IG






























