Choose upright Charcoal boards and P01 details for this composite fence gate. Eight boards and two P01 decorative panels form the complete two-leaf layout. The boards run upright; the decorative panels remain separate items, with their own materials and purchase quantities.
One LINE crossbeam serves this double fence gate at its dedicated 7 ft fence connection. This does not change the nominal 6 ft leaf height or make the nominal 7 ft width a clear-opening measurement. Two 114-inch posts use the 86-inch above-ground and 28-inch embedded arrangement. Assemble the separate infill into the aluminum frames and include the lock, handle set and beam fittings. Compare double-gate configurations when selecting the entrance layout.
Choose upright Charcoal boards and P01 details for this composite fence gate. Eight boards and two P01 decorative panels form the complete two-leaf layout. The boards run upright; the decorative panels remain separate items, with their own materials and purchase quantities.
One LINE crossbeam serves this double fence gate at its dedicated 7 ft fence connection. This does not change the nominal 6 ft leaf height or make the nominal 7 ft width a clear-opening measurement. Two 114-inch posts use the 86-inch above-ground and 28-inch embedded arrangement. Assemble the separate infill into the aluminum frames and include the lock, handle set and beam fittings. Compare double-gate configurations when selecting the entrance layout.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
Decorative Panel: electrocoated and powder-coated galvanized steel.
Decorative Panel Top Rail: powder-coated aluminum.
Decorative Panel Bottom Rail: powder-coated aluminum.
Decorative Panel Side Rail: powder-coated aluminum.
- Eight vertical Charcoal boards fill the composite portion of both leaves.
- Two separate Pattern P01 panels add the specified decorative infill.
- Only one crossbeam is used over the complete gate pair.
- The two In-Ground posts follow the dedicated 86/28-inch dimensions.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Charcoal Fence Board x 2 packs (8 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ 1 Foot x 6 Feet Fence Decorative Panel x 2 sets
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Charcoal boards and covered metal gate parts: up to 25 / 10 years.
- Covered Charcoal board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Is this the same board count as a plain vertical double gate?
No. This P01 configuration uses eight composite boards plus two decorative panels. The plain vertical full-privacy version has a different infill requirement.
Does the crossbeam turn the patterned gate into full privacy?
The beam is above the leaves and does not close the decorative pattern. The infill retains the P01 design.
Are the two board packs a complete gate kit?
They supply the eight-board allocation only. The frames, decorative panels, posts, beam and listed hardware are separate components for the full double gate.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPV/DGDP16P01CH8DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPH/DGDP16P01CH18DP2-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPV/DGFPCH12-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGG10CH20-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01CH18DP2-84X72-IG
In-Ground
Without Crossbeam
Style #: WPV/DGFPCH12-84X72-IG






























