Spaced horizontal Charcoal infill runs across the two aluminum frames of this composite double gate. Each leaf has nine full pieces, a solid terminal strip and eight 1-inch gaps. Private Black frames outline the nominal 7 ft W × 6 ft H pair.
One leaf opens for daily passage while the drop rod holds the companion, or both open for wider access. The In-Ground steel supports also carry one LINE steel crossbeam above the six-foot leaves, connecting this configuration to a seven-foot fence.
Spaced horizontal Charcoal infill runs across the two aluminum frames of this composite double gate. Each leaf has nine full pieces, a solid terminal strip and eight 1-inch gaps. Private Black frames outline the nominal 7 ft W × 6 ft H pair.
One leaf opens for daily passage while the drop rod holds the companion, or both open for wider access. The In-Ground steel supports also carry one LINE steel crossbeam above the six-foot leaves, connecting this configuration to a seven-foot fence.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
1-inch Spacer: powder-coated aluminum.
- Charcoal composite boards give this spaced entrance its infill color.
- The 1-inch openings retain visibility through the horizontal layout.
- Two aluminum frame sets carry a total of 20 composite infill pieces.
- One crossbeam serves the gate pair at the specified 7 ft fence junction.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Charcoal Fence Board x 5 packs (20 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ Accessory – 1-Inch Spacer for Horizontal Fence (40-Pack) x 0.8 pack (1-inch Spacer x 32 PCs)
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Charcoal boards and covered metal gate parts: up to 25 / 10 years.
- Covered Charcoal board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Are the openings the same as a closed-board gate?
No. This is the 1-inch-gap semi-privacy layout.
Which mounting type does this configuration use?
This configuration uses In-Ground.
Does adding the beam remove the In-Ground requirement?
No. This version uses two 114-inch In-Ground posts, with 86 inches above ground and 28 inches embedded. It is not a Surface Mount gate configuration.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPH/DGG10CH20-84X72-IG
In-Ground
With Crossbeam
Style #: WPH/DGFPCH22-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGDP16P01CH18DP2-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPH/DGFPCH22-84X72-IG
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01CH18DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPV/DGFPCH12-84X72-CB-IG






























