Combine horizontal Charcoal boards and Pattern P01 panels in this composite fence gate. The complete layout uses 18 composite boards and two decorative panels within a pair of aluminum frames. P01 identifies the patterned infill; the layout should not be treated as an uninterrupted full-privacy board stack.
One separate LINE crossbeam is specified above the leaves for the junction with a 7 ft fence. The double fence gate remains nominally 7 ft wide by 6 ft high. At this junction, the specified posts extend 86 inches above ground and 28 inches into the ground. Board packs, decorative panel sets and beam stock each have their own purchase allocation. Our composite gate collection helps compare patterned infill with closed and spaced alternatives.
Combine horizontal Charcoal boards and Pattern P01 panels in this composite fence gate. The complete layout uses 18 composite boards and two decorative panels within a pair of aluminum frames. P01 identifies the patterned infill; the layout should not be treated as an uninterrupted full-privacy board stack.
One separate LINE crossbeam is specified above the leaves for the junction with a 7 ft fence. The double fence gate remains nominally 7 ft wide by 6 ft high. At this junction, the specified posts extend 86 inches above ground and 28 inches into the ground. Board packs, decorative panel sets and beam stock each have their own purchase allocation. Our composite gate collection helps compare patterned infill with closed and spaced alternatives.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
Decorative Panel: electrocoated and powder-coated galvanized steel.
Decorative Panel Top Rail: powder-coated aluminum.
Decorative Panel Bottom Rail: powder-coated aluminum.
Decorative Panel Side Rail: powder-coated aluminum.
- Eighteen horizontal Charcoal boards are combined with two P01 panels.
- The decorative panels are separate infill components from the composite boards.
- Two aluminum frame sets provide the on-site gate assembly.
- One LINE crossbeam belongs to this dedicated 7 ft fence connection.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Charcoal Fence Board x 4.5 packs (18 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ 1 Foot x 6 Feet Fence Decorative Panel x 2 sets
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Charcoal boards and covered metal gate parts: up to 25 / 10 years.
- Covered Charcoal board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Do the eighteen boards include the P01 panels?
No. Eighteen is the composite board count for the pair. Two Pattern P01 decorative panels are listed separately and should be included in the purchase plan.
Does P01 mean the entire gate blocks every view?
No. The decorative panel has a patterned design. Do not treat this configuration as a completely closed board-only privacy gate.
Is one beam required above each patterned leaf?
The complete double gate uses one crossbeam, not two. It has its own LINE stock allocation and matching installation hardware.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01CH18DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPV/DGDP16P01CH8DP2-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGFPCH22-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGG10CH20-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPV/DGDP16P01CH8DP2-84X72-IG
In-Ground
Without Crossbeam
Style #: WPH/DGFPCH22-84X72-IG






























