Upright Redwood boards define this P01 composite fence gate. The layout uses eight boards together with two decorative panels across two aluminum frames. This is a patterned infill choice, distinct from both the plain full-privacy version and a horizontal board arrangement.
One separate LINE crossbeam is specified above the leaves for the connection to a 7 ft fence. The double fence gate is nominally 6 ft high and 7 ft wide across the pair. Steel posts use 86 inches above ground and 28 inches embedded. Keep the beam's stock allocation separate from the two-pack composite board requirement when preparing the order. Compare the available double gates before settling on the infill direction and decorative layout.
Upright Redwood boards define this P01 composite fence gate. The layout uses eight boards together with two decorative panels across two aluminum frames. This is a patterned infill choice, distinct from both the plain full-privacy version and a horizontal board arrangement.
One separate LINE crossbeam is specified above the leaves for the connection to a 7 ft fence. The double fence gate is nominally 6 ft high and 7 ft wide across the pair. Steel posts use 86 inches above ground and 28 inches embedded. Keep the beam's stock allocation separate from the two-pack composite board requirement when preparing the order. Compare the available double gates before settling on the infill direction and decorative layout.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
Decorative Panel: electrocoated and powder-coated galvanized steel.
Decorative Panel Top Rail: powder-coated aluminum.
Decorative Panel Bottom Rail: powder-coated aluminum.
Decorative Panel Side Rail: powder-coated aluminum.
- Eight Redwood boards run vertically in the complete two-leaf layout.
- Two P01 decorative panels are separate from the composite board allocation.
- One overhead LINE crossbeam is required for this selected configuration.
- The gate is specified for an In-Ground connection with a 7 ft fence.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Redwood Fence Board x 2 packs (8 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ 1 Foot x 6 Feet Fence Decorative Panel x 2 sets
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Redwood boards and covered metal gate parts: up to 25 / 10 years.
- Covered Redwood board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
How does this differ from the Redwood horizontal P01 gate?
The boards run vertically and the total board requirement is eight. The horizontal P01 configuration uses a different board count; do not transfer its materials list to this gate.
Do the 114-inch posts stand fully above ground?
No. This version specifies 86 inches above ground and 28 inches embedded. Post stock length, above-ground height and nominal leaf height are separate measurements.
Can two beams be assumed because there are two leaves?
No. The source specifies one crossbeam over the complete double gate. Follow its beam stock and fittings entries instead of assigning a beam to each leaf.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPV/DGDP16P01RD8DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPH/DGDP16P01RD18DP2-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPV/DGFPRD12-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGG10RD20-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01RD18DP2-84X72-IG
In-Ground
Without Crossbeam
Style #: WPV/DGFPRD12-84X72-IG






























