Select horizontal Redwood boards and P01 panels for this composite fence gate. Eighteen boards and two decorative panels are used across the full gate. The powder-coated aluminum frames, composite boards and patterned metal panels are different components, each identified separately in the purchase list.
One LINE crossbeam spans this double fence gate at the connection to a 7 ft fence. It retains the nominal 7 × 6 ft gate size and uses 114-inch steel posts with 86 inches above ground and 28 inches embedded. Check the installation opening independently of the nominal width. For alternative board directions and privacy layouts, use the composite gate overview alongside this configuration's specifications and component quantities.
Select horizontal Redwood boards and P01 panels for this composite fence gate. Eighteen boards and two decorative panels are used across the full gate. The powder-coated aluminum frames, composite boards and patterned metal panels are different components, each identified separately in the purchase list.
One LINE crossbeam spans this double fence gate at the connection to a 7 ft fence. It retains the nominal 7 × 6 ft gate size and uses 114-inch steel posts with 86 inches above ground and 28 inches embedded. Check the installation opening independently of the nominal width. For alternative board directions and privacy layouts, use the composite gate overview alongside this configuration's specifications and component quantities.
Engineering Dimensions
Nominal size (width × height): 7 × 6 ft.
Mounting Type: In-Ground.
Gate height: 72 inches.
Gap below the gate: 1 inch.
Post spacing (center to center): 87⅛ inches.
Clear opening between posts: approximately 84 inches.
Post height above ground: 86 inches, excluding the post cap.
Crossbeam top: 2 inches below the post top.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Hinge positions: 8 / 28½ / 8 inches.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
71 x 42-inch Welded Gate Frame: powder-coated aluminum.
Gate Frame Cover Strip: powder-coated aluminum.
#8 x 3/4" ST Screw: 410 stainless steel.
#8 x 1-1/4" ST Screw: 410 stainless steel.
#10 x 1" ST Screw: 410 stainless steel.
Composite Fence Board: wood-plastic composite (WPC).
Gate Stopper: powder-coated aluminum.
Gate Stop Cover Plate: powder-coated aluminum.
Hinge: powder-coated aluminum.
Groove Cover: powder-coated aluminum.
Crossbeam: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
Mechanical Combination Lock: 304 stainless steel.
Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.
#8 x 3/4" ST Screw: 316 stainless steel.
Decorative Panel: electrocoated and powder-coated galvanized steel.
Decorative Panel Top Rail: powder-coated aluminum.
Decorative Panel Bottom Rail: powder-coated aluminum.
Decorative Panel Side Rail: powder-coated aluminum.
- Horizontal Redwood boards combine with the separate P01 decorative infill.
- Eighteen boards and two panels cover the complete pair of gate leaves.
- The additional crossbeam is made from LINE stock rather than a composite board.
- The post arrangement is specific to this gate's 7 ft fence junction.
- Modern Yard™ 114-inch Steel Post x 2 PCs
- Modern Yard™ 71-inch x 42-inch Door Frame x 2 sets
- Modern Yard™ Redwood Fence Board x 4.5 packs (18 boards)
- Modern Yard™ Stainless Steel Mechanical Combination Lock x 1 set
- Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod x 1 set
- Modern Yard™ 1 Foot x 6 Feet Fence Decorative Panel x 2 sets
- Modern Yard Line™ Fence Slat x 0.5 pack (1 crossbeam after cutting)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 0.5 set (Base Connector x 2 PCs, L Connector x 2 PCs, #8 x 3/4" ST Screw x 8 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in Redwood boards and covered metal gate parts: up to 25 / 10 years.
- Covered Redwood board color changes: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Related Components
Frequently asked questions
Are the decorative panels supplied inside the Redwood board packs?
No. The composite board packs and the two P01 panel sets are separate product allocations. Both appear in the complete materials list.
Is the entrance 7 ft high once ordered?
The leaves are nominally 6 ft high. The nominal 7 ft dimension is the width across both leaves, while the adjacent fence requirement identifies the crossbeam application.
Does the handle set replace the mechanical lock?
They are listed as different components. This double-gate configuration includes purchase entries for both the mechanical combination lock and the outdoor handle set with drop rod.
You Might Also Like
In-Ground
Without Crossbeam
Style #: WPH/DGDP16P01RD18DP2-84X72-IG
In-Ground
With Crossbeam
Style #: WPV/DGDP16P01RD8DP2-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGFPRD22-84X72-CB-IG
In-Ground
With Crossbeam
Style #: WPH/DGG10RD20-84X72-CB-IG
In-Ground
Without Crossbeam
Style #: WPV/DGDP16P01RD8DP2-84X72-IG
In-Ground
Without Crossbeam
Style #: WPH/DGFPRD22-84X72-IG






























