top of page

Get a better sense of your project cost and materials.

modern-yard-logo-horizontal-black.webp

Redwood Composite Horizontal Full Privacy Double Gate with Crossbeam — 7 ft W × 6 ft H - In-Ground

Style #:

WPH/DGFPRD22-84X72-CB-IG

These composite double gates carry the horizontal Redwood board layout through the entrance. Twenty-two boards fill two separately supplied aluminum frames. Assemble the individual boards inside the frames to create the two composite panels. The composite fence gate combines wood-plastic composite infill with powder-coated metal parts. Cut one separately purchased LINE slat for the single crossbeam above both leaves.

Choose this version where the entrance meets a 7 ft fence. The paired gate is nominally 7 ft wide, while its leaves remain 6 ft high. The two steel posts have 86 inches above ground and 28 inches below. Those post dimensions belong to this crossbeam configuration.

When comparing composite gates, distinguish the board layout from the assembly and post requirements. Explore matching composite fence gates for other infill directions. Component Needs separates board stock, frame sets, posts, lock, handles and beam fittings so you can plan the complete order.

  • These composite double gates carry the horizontal Redwood board layout through the entrance. Twenty-two boards fill two separately supplied aluminum frames. Assemble the individual boards inside the frames to create the two composite panels. The composite fence gate combines wood-plastic composite infill with powder-coated metal parts. Cut one separately purchased LINE slat for the single crossbeam above both leaves.

    Choose this version where the entrance meets a 7 ft fence. The paired gate is nominally 7 ft wide, while its leaves remain 6 ft high. The two steel posts have 86 inches above ground and 28 inches below. Those post dimensions belong to this crossbeam configuration.

    When comparing composite gates, distinguish the board layout from the assembly and post requirements. Explore matching composite fence gates for other infill directions. Component Needs separates board stock, frame sets, posts, lock, handles and beam fittings so you can plan the complete order.

  • Engineering Dimensions

    Nominal size (width × height): 7 × 6 ft.

    Mounting Type: In-Ground.

    Gate height: 72 inches.

    Gap below the gate: 1 inch.

    Post spacing (center to center): 87⅛ inches.

    Clear opening between posts: approximately 84 inches.

    Post height above ground: 86 inches, excluding the post cap.

    Crossbeam top: 2 inches below the post top.

    Post depth below ground: 28 inches.

    Concrete footing width: 12 inches min.

    Hinge positions: 8 / 28½ / 8 inches.

    Parts and Materials

    Standard Post Cap: powder-coated aluminum.

    114-inch Steel Post: powder-coated galvanized steel.

    3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).

    71 x 42-inch Welded Gate Frame: powder-coated aluminum.

    Gate Frame Cover Strip: powder-coated aluminum.

    #8 x 3/4" ST Screw: 410 stainless steel.

    #8 x 1-1/4" ST Screw: 410 stainless steel.

    #10 x 1" ST Screw: 410 stainless steel.

    Composite Fence Board: wood-plastic composite (WPC).

    Gate Stopper: powder-coated aluminum.

    Gate Stop Cover Plate: powder-coated aluminum.

    Hinge: powder-coated aluminum.

    Groove Cover: powder-coated aluminum.

    Crossbeam: powder-coated galvanized steel.

    Base Connector: powder-coated aluminum.

    L Connector: 201 stainless steel.

    Mechanical Combination Lock: 304 stainless steel.

    Outdoor Gate Handle Set with Drop Rod: 304 stainless steel.

    #8 x 3/4" ST Screw: 316 stainless steel.

    • Twenty-two Redwood boards form the horizontal full-privacy infill across both gate leaves.
    • Two powder-coated aluminum frames hold the composite boards for assembly on site. The composite boards need no regular painting or staining.
    • One separate LINE crossbeam spans the complete double-gate arrangement, rather than one beam per leaf.
    • The dedicated In-Ground post layout joins a 7 ft fence while keeping the moving leaves nominally 6 ft high.
  • Limited warranty periods (residential / commercial use):

    • Structural defects in Redwood boards and covered metal gate parts: up to 25 / 10 years.
    • Covered Redwood board color changes: up to 25 / 10 years.
    • Coastal metal coating defects: up to 5 / 3 years.
    • Non-coastal metal coating defects: up to 15 / 10 years.
    • Covered metal finish fading, all locations: up to 8 / 5 years.

    For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.

    Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes. The combination lock and outdoor handle set are outside the periods listed above. Contact Modern Yard for the applicable separate warranty terms.

    Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.

    Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.

    For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.

    Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.

    We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.

    Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.

Related Components

Modern Yard 114-inch galvanized steel fence post with compatible fence system components

Modern Yard™ 114-Inches Steel Post

Modern Yard Redwood composite fence board with wood-look finish on a white background

Modern Yard™ Redwood Fence Board (4-Pack)

Modern Yard LINE 1 x 4 x 8 ft galvanized steel fence slat with dark powder-coated finish

Modern Yard Line™ Fence Slat - 1 in. x 4 in. x 8 ft (2-Pack)

Modern Yard 71 x 42 aluminum gate frame on a white background

Modern Yard™ 71 Inches x 42 Inches Gate Frame

Modern Yard 304 stainless steel mechanical combination gate lock

Modern Yard™ Stainless Steel Mechanical Combination Lock

Modern Yard stainless steel outdoor gate handle set with drop rod

Modern Yard™ Stainless Steel Outdoor Gate Handle Set with Drop Rod

Modern Yard full-privacy hardware kit for 1-inch horizontal fence slats

Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats

Imagine Your Future Fence

​Installation Guides

Installation Manual

​Technical Drawing


Frequently asked questions

No. Twenty-two boards cover both leaves together. Their material allocation is 5.5 four-board packs, not 22 packs or a preassembled filled gate. For a combined project, total the Redwood boards and usable stock before buying complete packs. Do not round each allocation separately and treat it as the final order.

This version adds a separate crossbeam for a 7 ft fence connection. Use its own post layout: 86 inches above ground and 28 inches below from each 114-inch post. The gate leaves remain nominally 6 ft high. The ordinary version has its own installation dimensions, so do not interchange the two layouts.

Keep the Redwood board stock, two frame sets and separate beam stock as different products. The lock, handle set and posts also have their own entries.

The LINE allocation is half a two-slat pack for one crossbeam after cutting. Its separate half-set hardware share covers two Base Connectors, two L Connectors and eight fixing screws. Whole-pack purchases depend on the combined project requirements and available stock.


bottom of page