top of page

Get a better sense of your project cost and materials.

modern-yard-logo-horizontal-black.webp

Redwood Composite Vertical Full Privacy Fence Panel — 8 ft W × 6 ft H - Surface Mount

Style #:

WPV/FPRD16-96X72-SM

Redwood composite fence boards give this Surface Mount composite fence a closed vertical face with a natural wood appearance. Sixteen upright pieces fill the nominal 8 × 6 ft section between Private Black metal posts. The full-privacy pattern uses joined board faces rather than spaced horizontal rows.

The wood plastic composite material blends wood fibers with recycled plastic. Redwood surfaces resist moisture, insects, rot and fading and need no regular painting, staining or sealing. Explore the vertical composite fencing arrangements when comparing the look of upright and horizontal infill.

A Vertical Fence Rail Set frames the composite board ends. Its powder-coated galvanized steel U rails connect through aluminum fittings. The board packs, rail set and steel posts are separate products, so plan all three when ordering a complete fence section.

This Surface Mount version uses 74-inch posts with welded base plates. The fence height is 72 inches, leaving the stated posts two inches above its upper edge before caps. A half-inch ground gap remains below the fence. Supply ground anchors separately for the bases.

Four four-board packs provide the sixteen pieces. For connected composite fencing systems, count each support location once and allow for free ends. One independent panel needs two welded-base posts.

  • Redwood composite fence boards give this Surface Mount composite fence a closed vertical face with a natural wood appearance. Sixteen upright pieces fill the nominal 8 × 6 ft section between Private Black metal posts. The full-privacy pattern uses joined board faces rather than spaced horizontal rows.

    The wood plastic composite material blends wood fibers with recycled plastic. Redwood surfaces resist moisture, insects, rot and fading and need no regular painting, staining or sealing. Explore the vertical composite fencing arrangements when comparing the look of upright and horizontal infill.

    A Vertical Fence Rail Set frames the composite board ends. Its powder-coated galvanized steel U rails connect through aluminum fittings. The board packs, rail set and steel posts are separate products, so plan all three when ordering a complete fence section.

    This Surface Mount version uses 74-inch posts with welded base plates. The fence height is 72 inches, leaving the stated posts two inches above its upper edge before caps. A half-inch ground gap remains below the fence. Supply ground anchors separately for the bases.

    Four four-board packs provide the sixteen pieces. For connected composite fencing systems, count each support location once and allow for free ends. One independent panel needs two welded-base posts.

  • Engineering Dimensions

    Nominal size (width × height): 8 × 6 ft.

    Mounting Type: Surface Mount.

    Fence height: 72 inches.

    Gap below the fence: ½ inch.

    Post spacing (center to center): 96⅜ inches.

    Clear opening between posts: approximately 93¼ inches.

    Post height above ground: 74 inches, excluding the post cap.

    Parts and Materials

    Standard Post Cap: powder-coated aluminum.

    74-inch Steel Post with Welded Base Plate: powder-coated galvanized steel.

    3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).

    Composite Fence Board: wood-plastic composite (WPC).

    Groove Cover: powder-coated aluminum.

    U Rail: powder-coated galvanized steel.

    End Cap: PA6.

    Top Rail Connector: powder-coated aluminum.

    Bottom Rail Connector: powder-coated aluminum.

    #8 x 3/4" ST Screw: 410 stainless steel.

    • Upright Redwood composite boards form the full-privacy infill across the eight-foot width.
    • The wood-grain faces resist moisture, insects, rot and fading.
    • Composite board surfaces need no regular paint, stain or sealer.
    • The vertical rail system connects the board body to welded-base steel post supports.
  • Limited warranty periods (residential / commercial use):

    • Structural defects in Redwood boards and covered metal fence parts: up to 25 / 10 years.
    • Covered Redwood board color changes: up to 25 / 10 years.
    • Coastal metal coating defects: up to 5 / 3 years.
    • Non-coastal metal coating defects: up to 15 / 10 years.
    • Covered metal finish fading, all locations: up to 8 / 5 years.

    For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.

    Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes.

    Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.

    Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.

    For approved claims, Modern Yard refunds or replaces defective boards or parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.

    Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.

    We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.

    Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.

Related Components

Modern Yard 74-inch galvanized steel fence post with welded base plate and compatible system components

Modern Yard™ 74-Inches Steel Post with Welded Base Plate

Modern Yard vertical fence rail set with matching rail and mounting components

Modern Yard™ Vertical Fence Rail Set

Modern Yard Redwood composite fence board with wood-look finish on a white background

Modern Yard™ Redwood Fence Board (4-Pack)

Imagine Your Future Fence

Installation Guides

Installation Manual

​Technical Drawing


Frequently Asked Questions

The four Redwood packs contain sixteen composite boards. Buy the Vertical Fence Rail Set separately for its steel U rails, aluminum connectors, end caps and supplied screws. The post products are also separate from the boards.

Use the specified steel posts with welded bases and provide the ground anchors. The drawing gives a 74-inch finished post height, excluding caps, around the 72-inch fence. The vertical rail set does not supply the post-to-ground anchors.

Use mild soap and water with a soft cloth or brush on the composite faces. Do not use abrasive tools or harsh chemicals. The Redwood boards require cleaning without regular painting, staining or sealing; this care statement applies to the composite portion.

bottom of page