This 8 ft wide × 7 ft high horizontal metal privacy fence uses twenty-one joined horizontal slats. Its Private Black LINE fence system has corrosion-resistant powder coating over galvanized steel. Matching steel fence posts support the infill. The drawing lists 1½ inches of ground clearance.
The slats' powder coating helps resist corrosion and outdoor wear. Straight rows give the fence clean lines. Full-privacy hardware joins the slats within the steel post system, without a separate horizontal rail set. Compare the metal fence options for other LINE patterns.
Buy eleven two-slat packs for one isolated section: use twenty-one pieces and keep one spare. Order the full-privacy hardware and 114-inch posts separately. For a longer run, combine slat quantities before rounding the packs and count each shared support once.
Two connected panels need forty-two slats and three posts along a straight run. Twenty-one packs supply the slats. Two isolated panels use four posts. Order slats for the whole project, then review any corner or gate connections before finalizing the parts.
The drawing places post centers 96⅜ inches apart, with approximately 93¼ inches clear between them. Use those measurements to lay out the supports. Seven feet names the nominal fence height; the posts extend 86 inches above ground without caps and retain 28 inches below. Ground clearance is a separate dimension.
This 8 ft wide × 7 ft high horizontal metal privacy fence uses twenty-one joined horizontal slats. Its Private Black LINE fence system has corrosion-resistant powder coating over galvanized steel. Matching steel fence posts support the infill. The drawing lists 1½ inches of ground clearance.
The slats' powder coating helps resist corrosion and outdoor wear. Straight rows give the fence clean lines. Full-privacy hardware joins the slats within the steel post system, without a separate horizontal rail set. Compare the metal fence options for other LINE patterns.
Buy eleven two-slat packs for one isolated section: use twenty-one pieces and keep one spare. Order the full-privacy hardware and 114-inch posts separately. For a longer run, combine slat quantities before rounding the packs and count each shared support once.
Two connected panels need forty-two slats and three posts along a straight run. Twenty-one packs supply the slats. Two isolated panels use four posts. Order slats for the whole project, then review any corner or gate connections before finalizing the parts.
The drawing places post centers 96⅜ inches apart, with approximately 93¼ inches clear between them. Use those measurements to lay out the supports. Seven feet names the nominal fence height; the posts extend 86 inches above ground without caps and retain 28 inches below. Ground clearance is a separate dimension.
Engineering Dimensions
Nominal size (width × height): 8 × 7 ft.
Mounting Type: In-Ground.
Fence height: 84 inches.
Gap below the fence: 1½ inches.
Post spacing (center to center): 96⅜ inches.
Clear opening between posts: approximately 93¼ inches.
Post height above ground: 86 inches, excluding the post cap.
Post depth below ground: 28 inches.
Concrete footing width: 12 inches min.
Parts and Materials
Standard Post Cap: powder-coated aluminum.
114-inch Steel Post: powder-coated galvanized steel.
3/4" U-Channel Rubber Strip: PVC (polyvinyl chloride).
Line™ Fence Slat: powder-coated galvanized steel.
Base Connector: powder-coated aluminum.
L Connector: 201 stainless steel.
#8 x 3/4" ST Screw: 410 stainless steel.
Groove Cover: powder-coated aluminum.
Slot Insert Strip: EVA (ethylene vinyl acetate).
- Twenty-one joined steel slats close the horizontal infill face.
- Private Black powder coating helps protect the galvanized steel from corrosion.
- Full-privacy connectors and EVA strips fit the closed slat pattern.
- Full-length 114-inch posts serve this seven-foot In-Ground layout.
- Modern Yard™ 114-inch Steel Post x 1 PC
- Modern Yard Line™ Fence Slat x 10.5 packs (21 slats)
- Modern Yard™ Full-Privacy Hardware Kit for 1-Inch Fence Slats x 1 set (Base Connector x 2 PCs, L Connector x 2 PCs, Slot Insert Strip x 4 PCs)
Limited warranty periods (residential / commercial use):
- Structural defects in covered metal fence parts: up to 25 / 10 years.
- Coastal metal coating defects: up to 5 / 3 years.
- Non-coastal metal coating defects: up to 15 / 10 years.
- Covered metal finish fading, all locations: up to 8 / 5 years.
For metal coating coverage, use the nearest shoreline of an ocean, sea or saltwater bay. Salt or brackish tidal estuaries also count. Measure in a straight line from the installed part. A distance of 10 miles or less is coastal; farther away is non-coastal.
Qualifying defects under normal use must meet the written terms, including color and coating claim conditions. Metal coverage applies only to covered parts and eligible factory finishes.
Normal airborne coastal salt and salt spray alone do not exclude qualifying coating claims. The metal warranty excludes direct saltwater immersion or splash damage.
Remaining coverage transfers with property ownership. Products must stay at the original site. Keep records of the products and original purchase date. Transfer or replacement does not restart coverage.
For approved claims, Modern Yard refunds or replaces defective parts. The original net purchase price determines the amount. The amount drops over time under the warranty schedule.
Metal coating compensation is 100% in the term’s first half, 50% in the second. Other claims follow separate schedules.
We do not pay for labor, installation, removal, reinstallation, freight or shipping. This changes if required by law or if Modern Yard expressly agrees in writing.
Email service@mymodernyard.com with purchase records, photos, product details and the issue. Expect a decision or next steps within 7–14 business days. Contact Modern Yard for full warranty terms.
Frequently Asked Questions
How does the closed panel differ from the half-inch layout?
The closed version uses twenty-one joined slats. The 8 × 7 ft half-inch LINE fence uses nineteen spaced slats with different hardware.
Why does Component Needs show 10.5 slat packs?
Two slats come in each pack. Twenty-one pieces use 10.5 packs of material; buy eleven complete packs for one bay.
Does one full-privacy kit determine the final hardware order?
Allow one full-privacy kit per panel, then check the complete order. Each section uses four EVA slot strips. Confirm that the kits provide enough connectors and continuous strip lengths. Add a full kit if the available material falls short.
You Might Also Like
In-Ground
Style #: LNH/FPPB18-96X72-IG
In-Ground
Style #: LNH/FPPB15-96X60-IG
In-Ground
Style #: LNH/G05PB19-96X84-IG
In-Ground
Style #: LNH/G10PB17-96X84-IG
In-Ground
Style #: LNH/G05PB16-96X72-IG
In-Ground
Style #: LNH/G10PB14-96X72-IG